Skip to main content

How to Replace A Light Switch

A light switch is often overlooked at how important it is around the house, until it no longer works correctly. When that happens, it is an easy task for any do it yourselfer to change out the broken light switch with a new one.

First thing to do is to figure out the type of light switch you will be working with.

There exist three varieties of light switch, a one-way switch, a two-way switch and an intermediate switch. All switches are rated at either 6 or 10 amps.

A one-way switch controls a light or lights from one position, usually by a door. A two-way switch is going to have a partner so that a light can be turned on and off from two positions, say by the kitchen door and the back door. An intermediate switch is utilized whenever the light is to be switched on or off from three positions or even more.

A one-way switch will have two terminals on the back for the wire connections, a two-way will have three and an intermediate will have four.

 

The first step to changing the switch, first turn on the light and then pull out or shut off the fuse or mcb, that will guarantee you have got the appropriate circuit, if the light goes out. Place the fuse in your pocket or tape down the mcb to ensure that it cannot be re-energized.

Take off the switch plate from the wall by removing the two screws and pull it gently towards you. If it sticks to the wall, with the screws removed, it has probably been painted in place, so carefully run a razor knife around the plate to break the seal. You can at this point observe the connections in the back.

At this point is an excellent time to make a note, a sketch, or even a picture of where the electrical wires are attached. Should you have a similar switch the terminations will be a straight replacement but if it looks different then make these notes.

The majority of switches comply with the same format for marking. ‘C’ for common, L1 and L2 for the others. One a one way switch the common is going to be the red/brown wire and L1 is going to take the black/blue wire with a short identifier of brown or red sleeving or tape.

With a two way switch it is not out of the ordinary to have five wires connected into the back. Making a note is highly suggested. The five wires are going to be split up into two pairs along with a common. The two pairs can be placed into either L1 or L2, it will not matter but the single wire must go into the common or the switch is useless.

After you remove the switch you will see some blue or black wires attached into a block, these are the neutrals and should never be hooked up to the other live wires otherwise you can cause an electrical short along with a small bang.

The earth or cpc wires can be left alone as well unless you are installing a metal switch in which case you must create a connection to the plate to the terminal supplied. This can easily be accomplished with a short bit of copper wire, ideally sleeved with green.

After you have made all the connections and are comfortable that they are accurate, carefully place the switch into the box, making certain all the wires are pushed clear of the screw positions and screw it down securely. Then replace the switch cover, or put a new one on and securely screw that into position.

Follow these tips and changing a light switch will not seem to be that difficult.

The post How to Replace A Light Switch appeared first on Downtown Homestead.



from Downtown Homestead http://downtownhomestead.com/replace-light-switch
Labels:

Comments

Post a Comment

Popular posts from this blog

Air Condition Your Garden

July, it is the time of the year when air conditioning is as important in the garden as it is in the home. You, as the temperature rises, can cool off with an electric fan, a cool drink or by hiding away in a cool spot. Your plants are not quite that lucky; yet certain gardening techniques can be employed to help your plants through the summer months. The benefits of air conditioning in your garden will show up in the form of increased production, greater resistance to disease and pests and, in general, a more attractive vista. An improper over-heated environment during the warmer months often leads to wilt, dropping of buds and yellowing of foliage. Aeration of the soil is concerned with its exposure to the air. If this is lacking then your plants very likely will suffer this summer. Believe it or not but there are millions of tiny spaces between the soil particles and this is where air resides. Soils that become water-logged force out this air, a condition that leads to souring of ...
Post a Comment
Read more

Plumbing Noises In Your Home: Your Pipes are talking to you

To diagnose plumbing noises, it is important to determine first whether the unwanted sounds occur on the system’s inlet side-in other words, when water is turned on-or on the drain side. Noises on the inlet side have varied causes: excessive water pressure, worn valve and faucet parts, improperly connected pumps or other appliances, incorrectly placed pipe fasteners, and plumbing runs containing too many tight bends or other restrictions. Noises on the drain side usually stem from poor location or, as with some inlet side noise, a layout containing tight bends.   Common Plumbing Noises Hissing Pipes Hissing noise that occurs when a faucet is opened slightly, generally signals excessive water pressure. Consult your local water company if you suspect this problem; it will be able to tell you the water pressure in your area and can install a pressure reducing valve on the incoming water supply pipe if necessary. Thudding Pipes Thudding noise, often accompanied by shuddering pipe...
Post a Comment
Read more

How to Save Your Own Set of Seeds

Saving seeds doesn’t have to be a frightening task and can even be absolutely easy, according to Fred Bove of the San Francisco Permaculture Guild . Instead of waiting for the last riffraff plants to flower, he instructs to look for the biggest, most colorful specimens that were among the first few plants to become ripe. He urges to resist harvesting the first beautiful flower, vegetable or herb of any one planting, and allow full maturity. “You want to save the best characteristics (of any plant) and pass them on,” explained Bove. Depending on the plant, you may want to select for size, flavor or how quickly it takes for the crop to reach maturity. “That way, you’re promoting the desired characteristics in the next generation of seeds.” The next important challenging task is identifying a seed that’s ready for saving. There are different ways to save seeds, depending on the variety. Plants in the apiaceae family, which includes parsley, fennel and cilantro, will bloom and form umbr...
Post a Comment
Read more